[BB 15000]

Je ne parviens pas à faire apparaître le BB15000 dans TS2019. Comme si le fichier, geopcdx est manquant?
J'ai la dernière version BB 15000 4.1.

Quelqu'un peut-il conseiller s'il vous plaît?

[SNCF DTG BR648]

Olaf ,

If you have erased the DTG 648 completely, why not try uninstalling it then re-installing it via Steam. If the Default loco then works oK, you can then unpack the .ap file fully again and then install the SNCF variant following my instructions. If the SNCF still causes problems delete all again and just re-install the default.

Thinking about you problem. Sometimes TS20XX can be very persistent in following previously set paths. That is why people are advised to always delete the blueprints .pak and Clear the game cache after installing anything.

If you go for a complete re-install one step at a time ( Default first and test then SNCF after fully unpacking the .ap, the delete blueprints and clear cache each time ), you will probably find that everything works. It would be a shame not to use the default loco since you have bought it. It is not that bad, although it is not as good as the Railtraction version.

 

springer

[SNCF DTG BR648]

Olaf,

Did you fully extract all the contents of your .ap file ? In Assets\DTG\BR648Pack01 you should have a "Audio", "InputMappers","Lights", "Particles","PreLoad",RailVehicles",,"Weather" folders as well as the .ap file.  In the RailVehicles folder there is a "Diesel" folder. In that you should have "BR648" and "SNCF". In the SNCF\Engine you should have copied in the 2 .GEOPCDX files.

If you have all that, then make sure you have deleted the blueprints.pak file from the main folder and then cleared the game's cache after you have finished all the above installation  changes.

If after checking and doing all that, you still do not have any horn or diesel engine sounds, I do not know what to suggest  ?? I have just re-installed my reskin again as per above and I have all the sounds as they should be.

Good luck

springer

[SNCF DTG BR648]

Olaf ,

If you have no sound, did you extract all the "BR648Pack01Assets"  .ap file or just drag the RailVehicles bit out of the archive? 

If it was the latter, try completely unpacking the .ap file by using the "Extract Here" method I described. The reskin's .bin file calls for the audio ( and other items)  from the main "BR648Pack01" folder. Sometimes a .bin file will not look inside the .ap file, so you may have to extract everything in the .ap  to get all the features to work.

The sounds are fine for me (when all was extracted) and of 150 downloads , no one else has complained of no audio. Let me know if you solve it.

Be aware also that the DTG BR648 has an unusual start up procedure. You have to operate the engine start lever and then release it for a few seconds before it starts. Also the handbrake is on by default ! No mention of this in the manual !

I posted on Railsim-fr rather than Railsim-de as it is of course for use on French routes and primarily on Steam Workshop scenarios where DTG published content has to be used. Nevertheless , until we have something better, I use it as an X73500/X73900 substitute. The single unit Railtraction BR640 would have been a better choice, but that cannot be used in the Steam Workshop.

 

springer

 

[SNCF DTG BR648]

No problem Olaf. Glad you sorted it !

[SNCF DTG BR648]

Olaf ,

When you go into Assets\DTG\BR648Pack01 you will find "BR648Pack01Assets"  Type =AP File.

You need to unpack this .ap file, as you do with all DTG and most other downloads, before you can install any add-ons or reskins.

To unpack an .ap file, first make sure you have a suitable program installed.  "7-zip " is a good one and it is free.

When you have 7-zip, right click on the .ap file , hover on 7-zip and then left click on "Extract Here".

All the contents of the .ap file will then appear in your BR648Pack01 folder and you can follow my installation instructions.

Apologies for not mentioning .ap files. I wrongly assumed that most people knew you had to unpack them before making any changes or add-ons.

Note : If you don't want to unpack the whole .ap file, you can also select "Open Archive" rather than "Extract Here". You will then be able to just drag just the "RailVehicles" folder from the displayed archive into your BR648Pack01 folder.

I hope this helps ?

Best wishes

springer6

 

 

[SNCF BR 442]

Bonjour, le 442 fonctionne-t-il dans un scénario Standard ou Freeroam?
Parfois, reskins ne fonctionne pas dans Quick Drive. Je ne suis pas sûr pourquoi.

[SNCF BR 442]

Paul,

“mais lorsque je clique dessus pour "mettre le train sur les rails", le train n'apparaît pas.”

Cela est normalement dû à l'absence ou à la corruption des fichiers .geopcdx. Vérifiez que vous copiez et collez les fichiers appropriés à partir de votre BR442Pack01.
Springer

[SNCF BR 442]

Paul,
Bonjour. Quand vous dites "ça ne marche pas". Que veux-tu dire exactement ?
La version de SNCF apparaît-elle dans votre liste de locomotives «Editeur de scénario»? Il doit être répertorié comme suit: “DB Regio BR 442-2_SNCF”, DB Regio BR 442-7_SNCF ”etc.
S'il est répertorié mais n'apparaîtra pas une fois placé dans le scénario, avez-vous copié tous les fichiers .GEOPCDX requis?
Faites-moi savoir si vous avez encore des problèmes. Pardon mon pauvre français

Springer

[Marseille à Avignon en Unité Multiple]

Merci beaucoup. Excellente scénario, beaucoup mieux que les défaut les DTG